This project introduces the novice machinist to several basic machine shop (bench work) operations as well as introducing basic notions on organizing and preparing a project. More specifically this video presents the basic layout of holes, positional punching (prick and center) as well as the drilling of small holes.
Premier de trois films décrivant la fabrication d'une jauge à foret. Plus particulièrement, ce film introduit le traçage , le poinçonnage et le perçage des petits trous.
This video presents the taping of small holes, contour line layout, hack sawing, cross filing and draw filing.
Cette vidéo introduit le taraudage, le traçage du contour, le traçage permanent ainsi que le découpage.
This video presents contour filing, letter stamping and surface finishing using only hand tools.
Cette vidéo nous introduit au limage à traits croisés, au limage à traits tirés, au lettrage et à la finition.
This video answers Teun's question from the Netherlands about how to produce the graduated scale on the
drill point gauge project.
Cette vidéo répond à la question de Teun des Pays Bas qui demande: Comment produire l'échelle graduée de la jauge à foret?
First part of a six part video describing the machining of a machinist's positioning hammer. This project introduces the novice (beginner) machinist to several basic metal lathe operations as well as introducing basic notions on organizing and preparing a project. More specifically this video presents basic dimension layout, surfacing and center drilling on a metal lathe as well as describing the lathe's major components.
Dans cette vidéo d'introduction au tour à métal nous regarderons le dessin d'assemblage et détaillé du projet, le surfaçage, le traçage ainsi que le perçage de trous de centre. Cette vidéo est la première de quatre vidéos décrivant l'usinage du manche du marteau de positionnement.
Second part of a six part video describing the machining of a machinist's positioning hammer. More specifically this video presents knurling, square groove cutting, deep hole drilling and reaming on a metal lathe.
Deuxième de quatre vidéos décrivant l'usinage du manche du marteau de positionnement. Dans cette vidéo nous regarderons le moletage, le rainurage, le perçage (alésage) d'un trou profond ainsi que l'alésage à l'alésoir du trou percé.
Third part of a six part video describing the machining of a machinist's positioning hammer. More specifically this video presents shoulder turning, square grooving, concave grooving and die threading.
Dans cette vidéo d'introduction au tour à métal nous regarderons le tournage parallèle d'un diamètre à épaulement, le taillage d'une rainure concave et le filetage à la filière.
Fourth part of a six part video describing the machining of a machinist's positioning hammer. This video shows how to machine tapers (taper turning) with a taper attachment as well as taper turning by tailstock offset.
Dans cette vidéo d'introduction au tour à métal nous regarderons deux méthodes de tournage conique. Premièrement à l'aide d'un dispositif (règle inclinable) de tournage conique et deuxièmement par désaxement de la poupée mobile.
This video presents the machining of the hammer's head. Compound rest taper turning, parallel turning, grooving and die threading on a metal lathe as well as basic math for tapers are presented.
Cette vidéo décrit l'usinage (sur un tour) de la tête du marteau de positionnement, plus particulièrement le taillage d'un cône par désaxement du chariot porte-outil.
This video presents the machining of the hammer handles plug as well as the striking tips. Accurate parallel turning, drilling and tapping of small parts held in a 5C collet on a metal lathe.
Ce film décrit l'usinage (sur un tour) des tables et du bouchon du marteau de positionnement.
This video introduces us to certain basic milling machine operations including surface milling, squaring a block, hole positioning and center drilling.
Dans cette vidéo nous regarderons certaines opération de base sur fraiseuse incluant le FRAISAGE E SURFACES PLANES, l'ÉQUARRISSAGE DE BLOC et le POINTAGE DE TROUS.
In this video we look at DRILLING, COUNTER BORING AND HEAT TREATMENT.
Dans cette vidéo, nous regarderons le PERÇAGE, le CHAMBRAGE et le TRAITEMENT THERMIQUE.
This video introduces us to HEAT TREATMENT and SURFACE GRINDING
Cette vidéo présente la PRÉPARATION EN VUE DE LA RECTIFICATION ainsi que la RECTIFICATION comme tel.
This series of videos introduces us to certain basic turning, threading and finishing operations. Keeping in mind that the objective of my videos is to introduce novice machinists to accurate work techniques. This video presents a progressive approach to completing a complex multi part project requiring the use of a lathe and machine shop hand tools.
Première d'une série de vidéos décrivant l'usinage d'un vérin de fraisage. Plus particulièrement, cette vidéo introduit le projet et nous prépare pour l'usinage d'un projet multi pièces sur le tour incluant plusieurs techniques de travail à l'établi.
In this second video of this series we will be looking at how to machine the screw jacks ball that is the contact point between the screw jack and a part.
Deuxième d'une série de vidéos décrivant l'usinage d'un vérin de fraisage. Plus particulièrement, cette vidéo démontre comment usiner une bille qui servira de point d'appui entre le vérin et une pièce.
In this third video of the this series, we will look at how to cut an external thread on the lathe as well as the required calculations.
Troisième d'une série de vidéos décrivant l'usinage d'un vérin de fraisage. Plus particulièrement, cette vidéo nous montre comment tailler un filet externe sur un tour et les calculs requis.
In this fourth video of the series, we will looking at how to tap a thread on the lathe, how to use the threaded hole produced as a fixture, how to cut a taper using the compound rest, how to heat treat our ball rest and how to set the ball by curling an edge.
Quatrième d'une série de vidéos décrivant l'usinage d'un vérin de fraisage. Plus particulièrement nous regarderons comment tarauder un trou sur le tour, comment utiliser le trou taraudé comme un gabarit, comment tailler un cône, comment durcir notre bille de contact et comment rouler le bout du cône pour retenir la bille en place.
In this fifth video of the series, we will be looking at the preparation and threading of the mid section of the jack. We will then start machining the base. A little tip: If you want to know where we will be by the end of this video, look at the thumbnail on the left.
Cinquième d'une série de vidéos décrivant l'usinage d'un vérin de fraisage. Dans cette section nous regarderons la préparation et le filetage de la pièce centrale du vérin. Ensuite nous commencerons à usiner la base. Si vous voudriez savoir ou nous serons à la fin de cette vidéo, regardez la vignette à la droite de ce massage.
In this sixth and last video of the series, we will be looking at the preparation and internal threading (not tapping) of the base of the screw jack. Once we have completed the thread we will use the base (still mounted in the chuck) as a fixture in order to finish the middle section of the part.
Dans cet sixième et dernière vidéo de la série nous effectuerons le filetage intérieure (pas le taraudage) de la base du vérin. ensuite nous allons utiliser la base (sans le démonter du mandrin) comme gabarit pour finir la pièce intermédiaire du vérin.
This video series presents a progressive approach to completing a complex project requiring planning, the use of a milling machine, a shaper, a surface grinder and machine shop hand tools. In this first video of the V-BLOCK series we will mostly be looking at project planning.
Cette série de vidéos présente nous initie à une approche progressive pour compléter un projet complexe qui requiert de la planification, l'usage d'une fraiseuse, d'un étau limeur, d'une rectifieuse plane ainsi que plusieurs outils manuels. Cette première vidéo de la série BLOC EN V présente la planification du projet.
This second video of the V-BLOCK series is an introduction to shapers.
Cette seconde vidéo de la série BLOC EN V est une introduction à l'étaux limeur.
This third video of the V-BLOCK series we will start looking at the side grooves on the blocs
Cette troisième vidéo de la série BLOC EN V est une introduction
In this fourth video of the V-BLOCK series we will be finishing the lateral grooves.
Dans cette quatrième vidéo de la série BLOC EN V nous finirons les rainures latéraux.
This fifth video of the V-BLOCK series is all about drilling and tapping holes. We will be positioning holes using two separate methods. One for home shops (layout work) and one by coordinates with a milling machine.
Cette cinquième vidéo de la série BLOC EN V porte sur le perçage et le taraudage de trous avec deux approche différentes. La première par traçage de précision et le second par coordonnés cartésiens avec une fraiseuse.
In this sixth video of the V-BLOCK series we will be drilling
the through hole, roughing out the V and slotting the V.
Cette sixième vidéo de la série BLOC EN V porte sur le perçage du trou qui traverse le bloc, sur le dégrossissage du V et le rainurage du V.
In this seventh video of the V-BLOCK series we will be making the clamps for the blocks.
Dans cette septième vidéo de la série BLOC EN V regarderons la fabrication des serres du projets.
In this eight and final video of the V-BLOCK series we will be wrapping this up by looking at two methods for heat treating our three blocks and two methods for finishing them.
Dans cette huitième et dernière vidéo de la série BLOC EN V nous allons compléter le projets. Deux méthodes de traitements thermiques et deux méthode de finition sont au menu.